Free HP HPE6-A85 Exam Questions

Question 1

You are working with a pair of 6300M switches in a VSF stack. The switch has 48 SmartRate 5G ports, 2 SFP28 ports, and 2 SFP56 ports. Both SFP56 ports are used for stacking. You need to provide an LACP connection to another identical stack with the maximum available bandwidth possible. What should you configure?

A : a 16-member LAG using 2 SFP28 ports and 6 SR5 ports on each switch

B : an eight-member LAG using 4 SR5 ports on each switch

C : an eight-member LAG using 2 SFP28 ports and 2 SR5 ports on each switch

D : a four-member LAG using 2 SFP28 ports on each switch

Answer: A

Question 2

When using the network check page in Central, what kind of tests can you run on switches? (Select two.)

A : Speed test (iperf)

B : Ping test

C : A full hardware check, including a heavy memory check

D : LED-check.

E : PoE-check

Answer: B,E

Question 3

You are working with a pair of 6300M switches in a VSF stack. The switch has 48 SmartRate 5G ports, 2 SFP28 ports, and 2 SFP56 ports. Both SFP56 ports are used for stacking. You need to provide an LACP connection to another identical stack with the maximum available bandwidth possible. What should you configure?

A : a 16-member LAG using 2 SFP28 ports and 6 SR5 ports on each switch

B : an eight-member LAG using 4 SR5 ports on each switch

C : an eight-member LAG using 2 SFP28 ports and 2 SR5 ports on each switch

D : a four-member LAG using 2 SFP28 ports on each switch

Answer: A

Question 4

When using the network check page in Central, what kind of tests can you run on switches? (Select two.)

A : Speed test (iperf)

B : Ping test

C : A full hardware check, including a heavy memory check

D : LED-check.

E : PoE-check

Answer: B,E

Question 5

You have been asked to onboard a new Aruba 6300M in a customer deployment You are working remotely rather than on-site You have a colleague installing the switch The colleague has provided you with a remote console session to configure the edge switch You have been asked to configure a link aggregation going back to the cores using interfaces 1/1/51 and 1/1/52 The Senior Engineer of the project has asked you to configure the switch and 1Q uplink with these guidelines 1. Add VLAN 20 to the local VLAN database with name Mgmt 2. Add L3 SVl on VLAN 20 for Management using address 10 in the 10.1.1 0/24 subnet 3. Add LAG 1 using LACP mode active for the uplink 4 use vlan 20 as the native vlan on the LAG 5. Make sure the interfaces are all ON. Which configuration script will achieve the task?

A : ge1# conf t vlan 20 name Mgmt interface vlan 20 ip address 10.1.1.10/24 no shut interface lag 1 shut vlan access 20 lacp mode active Int 1/1/51.1/1/52 shut no routing lag 1 interface lag 1 no shut

B : gel# conf t vlan 20 name Mgmt interface vlan 20 ip address 10 1.1 10/24 no shut interface 1/1/51.1/1/52 shut vlan trunk native 20 vlan trunk allowed all lag 1 lacp mode active interface 1/1/51.1/1/52 no shut

C : gel# conf t vlan 20 name Mgmt interface vlan 20 ip address 10 1 1 10/24 no shut interface lag 1 shut vlan trunk native 20 vlan trunk allowed all lacp mode active Int 1/1/51.1/1/52 shut no routing lag 1 interface lag 1 no shut interface 1/1/51.1/1/52 no shut

D : nf t vlan 20 name Mgmt ip address 10 1 1.10/24 no shut interface lag 1 shut vlan trunk native 1 vlan trunk allowed all lacp mode active int 1/1/51.1/1/52 shut no routing interface lag 1 no shut interface 1/1/51.1/1/52 no shut

Answer: C