Free Cisco 300-615 Exam Questions

Become Cisco Certified with updated 300-615 exam questions and correct answers

Page: 1 / 45

Total 221 Questions | Updated On: Dec 05, 2024

Add To Cart

Question 1

Refer to the exhibit. The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs. Which configuration set must be added to the script to fix the issue?

A : switch(config-applet)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val50 poll-interval 1switch(config-applet)# action 0.2 cli enableswitch(config-applet)# action 0.5 cli switchto vdc Coreswitch(config-applet)# action 0.8 cli switchto vdc Distribution

B : switch(config-applet)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val50 poll-interval 1switch(config-applet)# action 0.2 cli config tswitch(config-applet)# action 0.5 cli switchto vdc Coreswitch(config-applet)# action 0.8 cli switchto vdc Distribution

C : switch(config-applet)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entryval 50 poll-interval 1switch(config-applet)# action 0.2 cli config tswitch(config-applet)# action 0.5 cli switchto vdc Coreswitch(config-applet)# action 0.8 cli switchto vdc Distribution

D : switch(config-applet)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entryval 50 poll-interval 1switch(config-applet)# action 0.2 cli enableswitch(config-applet)# action 0.5 cli switchto vdc Coreswitch(config-applet)# action 0.8 cli switchto vdc Distribution

Answer: D

Question 2

300-615-page127-image8

Refer to the exhibit. A network engineer traces the packet flow from the Veth991 of a blade server toward the

core switch. The switch reports performance issues. What is the role of the interface Eth1/7?

A : M network interface

B : bric interconnect uplink interface

C : M host interface

D : server interface

Answer: B

Question 3

300-615-page127-image46

Refer to the exhibit. RBAC is configured on the MDS switch for a new SAN administrator engineer to work on

the FSPF configuration. However, after the configuration is applied the engineer who was assigned the

FSPF_Admin role cannot perform any configuration changes. Which action resolves the issue?

A : Write rule 2 before rule 1

B : Remove rule 1 from the role

C : nfigure the switch license for RBAC

D : Reload the switch

Answer: A

Question 4

300-615-page127-image3

Refer to the exhibits. A switch is downgraded to an earlier release because of a problem with the current

release. After the switch is downgraded, it cannot forward traffic. Which action resolves the issue?

A : Enable ISSD after the downgrade is complete.

B : ll back to the original image.

C : Reload the switch.

D : ut and no shut the interfaces to the FEX.

Answer: B

Question 5

A vPC Type-1 inconsistency between two vPC peers in a VXLAN EVPN setup is discovered. Which two actions need to be attempted to resolve the issue? (Choose two.)

A : nfigure the NVE interfaces to be Up on both switches

B : t a different distributed gateway virtual MAC address.

C : t a different secondary IP addresses on NVE source-interface

D : nfigure the same VNI to multicast group maping.

E : t a different primary IP addresses on NVE source-interface.

Answer: A,D

Page: 1 / 45

Total 221 Questions | Updated On: Dec 05, 2024

Add To Cart