Free Cisco 300-410 Exam Questions

Become Cisco Certified with updated 300-410 exam questions and correct answers

Page: 1 / 153

Total 765 Questions | Updated On: Jul 29, 2025

Add To Cart

Question 1

Refer to the following output:

Router#show ip nhrp detail

10.1.1.2/8 via 10.2.1.2, Tunnel1 created 00:00:12, expire 01:59:47

TypE. dynamic, Flags: authoritative unique nat registered used

NBMA address: 10.12.1.2

What does the authoritative flag mean in regards to the NHRP information?

A : It was obtained directly from the next-hop server.

B : Data packets are process switches for this mapping entry.

C : NHRP mapping is for networks that are local to this router.

D : The mapping entry was created in response to an NHRP registration request.

E : The NHRP mapping entry cannot be overwritten.

Answer: A

Question 2

Which two solutions are used to overcome a flapping link that causes a frequent label binding exchange between MPLS routers? (Choose two)

A : Create link dampening on links to protect the session.

B : Increase input queue on links to protect the session.

C : Create targeted hellos to protect the session.

D : Increase a hold-timer to protect the session.

E : Increase a session delay to protect the session.

Answer: A,C

Question 3

How many labels are present in an MPLS Layer 3 packet traversing through the network without traffic engineering?

A : 1

B : 2

C : 3

D : 4

Answer: A

Question 4

Refer to the exhibit.

The administrator configured the network devise for end-to-end reachability, but the ASBRs are not propagation routes to each other. Which set of configuration resolves this issue?

A :

B :

C :

D :

Answer: A

Question 5

The network administrator configured CoPP so that all routing protocol traffic toward the router CPU is

limited to 1 mbps. All traffic that exceeds

this limit must be dropped. The router is running BGP and OSPF Management traffic for Telnet and SSH

must be limited to 500kbps.

access-list 100 permit tcp any any eq 179

access-list 100 permit tcp any any range 22 23

access-list 100 permit ospf any any

class-map CM-ROUTING

match access-group 100

class-map CM-MGMT

match access-group 100

policy-map PM-COPP

class CM-ROUTING

police 1000000 conform-action transmit

class CM-MGMT

police 500000 conform-action transmit

control-plane

service-policy output PM-COPP

No traffic is filtering through CoPP,which is resulting in high CPU utilization,which configuration resolves

the issue ?

A : no access-list 100access-list 100 permit tcp any any eq 179access-list 100 permit ospf any anyaccess-list 101 Permit tcp any any range 22 23!class-map CM-MGMTno match access-group 100match access-group 101

B : control-planeno service-policy output PM-COPPservice-policy input PM-COPP

C : No access-list 100access-list 100 permit tcp any any eq 179access-list 100 permit tcp any any range eq 22access-list 100 permit tcp any any range eq 23access-list 100 permit ospf any any

D : no access-list 100access-list 100 permit tcp any any eq 179access-list 100 permit ospf any anyaccess-list 101 Permit tcp any any range 22 23!class-map CM-MGMTno match access-group 100match access-group 101!control-planeno service-policy output PM-COPP service-policy input PM-COPP

Answer: D

Page: 1 / 153

Total 765 Questions | Updated On: Jul 29, 2025

Add To Cart